Submodular Synthesizer

Introduction

The ISHIZENO ONE is a submodular synthesizer. It decouples faceplate from electronics in order to provide fine-grain modularity. It is built around an iPod Touch used as touchscreen, dynamic patching controller, and digital signal processing unit. It provides 8 polyphonic channels, each of them being made of 6 analog ports and being supported by a dedicated Arduino Uno and an optional Arduino shield. Dynamic patching between analog ports is supported by a set of analog crosspoint switches.

Rationale

• Providing a mixed interface (analog and digital) for processing mixed signals (analog and digital)
• Making it easier to develop custom modules as Arduino shields with a generic faceplate
• Enhancing the haptic interface of modular analog synthesizers with end-to-end signal visualization
• Experimenting with Low-Frequency Patching (think LFO, but for patching)

8 Polyphonic Channels

Each of the 8 polyphonic channels provides:

• 6 analog ports (A0, A1, A2, A3, A4, A5)
• 2 small knobs
• 2 large concentric knobs
• 1 Arduino Uno
• 1 Arduino shield (optional)

Dynamic Patching

Patching across channels can be done in a traditional way through the faceplate's 3.5mm jack chassis sockets (48 of them), through the analog crosspoint switches, or through multi-channel shields. Using dynamic patching, any pair of ports of any pair of channels can be patched together, including two ports of the same channel. When the module is equipped with 8 switches, up to 16 concurrent patches can be established at a time. With 16 switches, this limit is increased to 32.

Dynamic patching is enabled by a matrix of 8 or 16 AD75019 analog crosspoint switches. These switches have no gain and a low 150 Ω resistance. No more than two switches are ever used on the analog signal path, thereby limiting the overhead resistance to 300 Ω.

Dynamic patching can be done through the graphical user interface provided by the iPod Touch, by downloading a patch from the Internet through the iPod Touch's WiFi connection, by scanning a QR code with the iPod Touch's front-facing camera, or by using a dedicated controller like the monome grid.

Submodular Architecture

Out of the box, the module does not provide any synthesis capabilities. Instead, these are added through optional Arduino shields, with up to 8 shields (one per channel). Programming of the module can be done through the Arduino of any channel and through the iOS operating system of the module's iPod Touch. For example, the iPod Touch could be used as software sequencer. The analog crosspoint switches can also be reconfigured dynamically in order to support low-frequency patching.

Arduino Shields

Every channel can be supported by an optional Arduino shield that is plugged onto the module's backplane. Because shields do not include any faceplate, controls, mounting hardware, or power connector, they should be much more cost effective than full-fledged Eurorack modules. As such, they are referred to as submodules, and the synthesizer is described as being submodular.

Examples of shields could include any of the following:

• Analog Filter
• Digital Signal Processor
• Envelope Generator
• Low Frequency Oscillator
• Mixer
• Oscillator
• Phase Shifter
• Sampler
• Sequencer
• Waveshaper
• Etc.

Multi-Channel Shields

By default, a shield is attached to a single channel, through a single Arduino Uno. That being said, some applications might require more than 6 analog ports and more than 4 potentiometers. For such a scenario, a multi-channel shield can be used, spanning any number of channels.

Arduino Uno

Every polyphonic channel is controlled by a dedicated Arduino Uno. The channel's analog ports are statically patched to the Arduino's analog inputs (A0, A1, A2, A3, A4, A5). Furthermore, all standard Arduino pins are exposed to any Arduino shield used to support its related polyphonic channel.

16-channel Oscilloscope

The module includes two AD7606 8-channel 24-bit analog to digital converters. This allows the built-in iPod Touch to be used as a low-frequency 16-channel oscilloscope. The 16 channels of the oscilloscope can be dynamically patched to the 48 analog ports of the module's 8 polyphonic channels through a series of 3 AD75019 analog crosspoint switches.

Digital Potentiometers

All faceplate knobs are digitally encoded and their 256-position settings are passed to the channel's shield through the ISCP bus of the channel's Arduino Uno. Additionally, the setting of a knob can be converted into a voltage level that can be patched to any analog port of the knob's channel.

Additional Features

• 2 spinner control knobs driving rotary encoders
• 1 USB port connected to the iPod Touch's lightning connector
• 1 stereo headphone output connected to the iPod Touch's headphone jack

Future Upgrades

All switches used for dynamic patching are mounted on PLCC sockets so that an 8-switch module can be upgraded to a 16-switch configuration later on. The first module will offer 8 polyphonic channels, but future modules might offer only 2 or 4.

Project Status

This module is at the early prototyping stage. Specifications will vary. All software will be released under an open source license and all hardware designs will be released under a Creative Common license. Unfortunately, no release timeframe can be announced at this point.

Additional Resources

• List of Parts

Feedback needed!

https://ishizeno.wordpress.com/

• ? mA +12V
• ? mA -12V
• ? mA 5V

No info about availability.

$1,495